Transcription
Cisco IE 4000 Switch Hardware InstallationGuideFirst Published: September 2015Last Updated: June 2020Cisco Systems, Inc.www.cisco.com
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGEWITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BEACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULLRESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE INCORPORATED HEREIN BYTHIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOURCISCO REPRESENTATIVE FOR A COPY.The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply withthe limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonableprotection against harmful interference when the equipment is operated in a commercial environment. This equipmentgenerates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instructionmanual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely tocause harmful interference, in which case users will be required to correct the interference at their own expense.The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply withthe limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation. If the equipmentcauses interference to radio or television reception, which can be determined by turning the equipment off and on, users areencouraged to try to correct the interference by using one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate theproduct.The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California,Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright 1981,Regents of the University of California.NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS AREPROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSEDOR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE ANDNONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTALDAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE ORINABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCHDAMAGES.Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses andphone numbers. Any examples, command display output, network topology diagrams, and other figures included in thedocument are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content isunintentional and coincidental.All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version forthe latest version.Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website atwww.cisco.com/go/offices.Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationshipbetween Cisco and any other company. (1721R) 2015–2020 Cisco Systems, Inc. All rights reserved.ii
PrefaceAudienceThis guide is for the networking or computer technician responsible for installing Cisco IE 4000 series switches. Weassume that you are familiar with the concepts and terminology of Ethernet and local area networking.PurposeThis guide documents the hardware features of the Cisco IE 4000 switches. It describes the physical and performancecharacteristics of each switch, explains how to install a switch, and provides troubleshooting information.For information about the standard Cisco IOS commands, ml?mode prod&level0 268438303ConventionsThis document uses the following conventions and symbols for notes, cautions, and warnings.Note: Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.Caution: Means reader be careful. In this situation, you might do something that could result in equipment damageor loss of data.Warning: This warning symbol means danger. You are in a situation that could cause bodily injury. Before you workon any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practicesfor preventing accidents. Use the statement number provided at the end of each warning to locate its translation inthe translated safety warnings that accompanied this device. Statement 1071The safety warnings for this product are translated into several languages in the Regulatory Compliance and SafetyInformation for the Cisco IE 4000 Switch that ships with the product. The EMC regulatory statements are also includedin that guide.Related PublicationsBefore installing, configuring, or upgrading the switch, see the release notes on Cisco.com for the latest information.These documents provide complete information about the switch and are available on Cisco.com: Regulatory Compliance and Safety Information for the Cisco IE 4000 Switch Release Notes for the Cisco IE 4000 Switch Cisco IE 4000 Switch Software Configuration Guide Device Manager online help (available on the switch)Cisco Systems, Inc.iiiwww.cisco.com
PrefaceObtaining Documentation, Obtaining Support, and Security GuidelinesThese compatibility matrix documents are available from this Cisco.com s/ps5455/products device support tables list.html Cisco Gigabit Ethernet Transceiver Modules Compatibility Matrix (not orderable but available on Cisco.com) Cisco Small Form-Factor Pluggable Modules Compatibility Matrix (not orderable but available on Cisco.com)Obtaining Documentation, Obtaining Support, and SecurityGuidelinesFor information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines,and also recommended aliases and general Cisco documents, see the monthly What’s New in Cisco ProductDocumentation, which also lists all new and revised Cisco technical documentation, w/whatsnew.htmliv
Product OverviewThe Cisco Industrial Ethernet (IE) 4000 Series is the latest addition to our ruggedized switching platforms and providessuperior high-bandwidth switching and proven Cisco IOS Software-based routing capabilities for industrialenvironments. The IE 4000 Series delivers highly secure access and industry-leading convergence using the CiscoResilient Ethernet Protocol (REP) and is built to withstand extreme environments while adhering to overall IT networkdesign, compliance, and performance requirements.The IE 4000 Series is ideal for industrial Ethernet applications where hardened products are required, including factoryautomation, energy and process control, intelligent transportation systems (ITS), oil and gas field sites, city surveillanceprograms, and mining. With improved overall performance, greater bandwidth, a richer feature set, and enhancedhardware, the Cisco IE 4000 Series complements the current industrial Ethernet portfolio of related Cisco industrialswitches.The Cisco IE 4000 can easily be installed in your network. Through a user-friendly web device manager, the Cisco IE4000 provides easy out-of-the-box configuration and simplified operational manageability to deliver advanced security,data, video, and voice services over industrial networks.Switch ModelsModelDescriptionIE-4000-4TC4G-E4 FE Combo DL ports, 4 GE combo UL ports, w/FPGAIE-4000-8T4G-E8 FE Copper DL ports, 4 GE combo UL ports, w/FPGAIE-4000-8S4G-E8 FE Fiber DL ports, 4 GE combo UL ports, w/FPGAIE-4000-4T4P4G-E4 FE Copper DL ports 4 FE Copper DL ports with POE1, 4 GE combo UL ports, w/FPGAIE-4000-16T4G-E16 FE Copper DL ports, 4 GE combo UL ports, w/FPGAIE-4000-4S8P4G-E4 FE Fiber DL ports 8 FE Copper DL ports with POE1, 4 GE combo UL ports, w/FPGAIE-4000-8GT4G-E8 GE Copper DL ports, 4 GE combo UL ports, w/FPGAIE-4000-8GS4G-E8 GE Fiber DL ports, 4 GE combo UL ports, w/FPGAIE-4000-4GC4GP4G-E4 GE Combo DL ports 4 GE Copper DL ports with POE1, 4 GE combo UL ports, w/FPGAIE-4000-16GT4G-E16 GE Copper DL ports, 4 GE combo UL ports, w/FPGAIE-4000-8GT8GP4G-E8 GE Copper DL ports 8 GE Copper DL ports with POE1, 4 GE combo UL ports, w/FPGAIE-4000-4GS8GP4G-E4 GE Fiber DL ports 8 GE Copper DL ports with POE1, 4 GE combo UL ports, w/FPGACisco Systems, Inc.1www.cisco.com
Product OverviewFront Panel Overview1. IE-4000-8GT8GP4G-E supports up to 240W PoE, consisting of eight ports of PoE (30 W per port; IEEE 802.3at)with temperature derating (131 F (55 C) at full 240W PoE power) and depending on the power source used.All other PoE-capable models support up to 120W PoE, either PoE (15.4 W per port; IEEE 802.3af) or PoE (30W per port; IEEE 802.3at) over the full operating temperature range.Front Panel OverviewThe illustrations in this section provide an overview of the variety of components available on the various switch modelsin this product family. Not all models are illustrated.Figure 1Cisco IE-4000-8GT8GP4G-E shown1SFP module slots (uplink ports)6Power connector DC-B210/100/1000 Ethernet ports (downlink ports)7Power connector DC-A3Flash memory card slot8RJ-45 console port4Alarm connector9USB mini-Type B (console) port15Protective ground connection10Dual-purpose ports (uplink ports)1. Use a screwdriver to remove the port cover and access the port.Ports and SlotsNote: Different configurations are available. Not all ports or slots are present in all configurations.2
Product OverviewPorts and Slots10/100/1000 BASE-T Downlink PortsYou can set the 10/100BASE-T downlink ports to operate at 10 or 100 Mb/s in full-duplex or half-duplex mode. You canalso set these ports for speed and duplex autonegotiation in compliance with IEEE 802.3AB. (The default setting isautonegotiate.) When set for autonegotiation, the port senses the speed and duplex settings of the attached device andadvertises its own capabilities. If the connected device also supports autonegotiation, the switch port negotiates the bestconnection (that is, the fastest line speed that both devices support, and full-duplex transmission if the attached devicesupports it) and configures itself accordingly. In all cases, the attached device must be within 328 feet (100 meters).100BASE-TX traffic requires Category 5 cable. 10BASE-T traffic can use Category 3 or Category 4 cables.When connecting the switch to workstations, servers, routers, and Cisco IP phones, make sure that the cable is astraight-through cable.You can use the mdix auto interface configuration command in the command-line interface (CLI) to enable the automaticmedium-dependent interface crossover (auto-MDIX) feature. When the auto-MDIX feature is enabled, the switch detectsthe required cable type for copper Ethernet connections and configures the interfaces accordingly. For configurationinformation for this feature, see the switch software configuration guide or the switch command reference.10/100/1000BASE-T Uplink PortsThe IEEE 802.3u 10/100/1000BASE-T uplink ports provide full-duplex 10, 100 or 1000 Mb/s connectivity over Category5 unshielded twisted pair (UTP) copper cabling. The default setting is autonegotiate. The cable can be up to 100 m(0.1 km) in length.100/1000 Mb/s SFP Module Downlink SlotsThe IEEE 802.3u 100 Mb/s SFP module downlink slots provide full-duplex 100 Mb/s connectivity over multi-mode (MM)fiber cables or single-mode (SM) fiber cables. These ports use a SFP fiber-optic transceiver module that accepts a dualLC connector. Check the SFP specifications for the cable type and length.100/1000 Mb/s SFP Module Uplink SlotsThe IEEE 802.3u 100 Mb/s SFP module uplink slots provide full-duplex 100 or 1000 Mb/s connectivity over multi-mode(MM) fiber cables or single-mode (SM) fiber cables. These ports use a SFP fiber-optic transceiver module that acceptsa dual LC connector. Check the SFP specifications for the cable type and length.Dual-Purpose Fast Ethernet Downlink PortsYou can configure the dual-purpose Fast Ethernet Downlink ports on the switch as either 10/100BASE-T ports or as 100Mb/s SFP-module ports. You can set the 10/100 ports to autonegotiate, or you can configure them as fixed 10 or 100Mb/s ports.By default, the switch selects the medium for each dual-purpose port (10/100BASE-T or SFP). When a link is achievedon one media type, the switch disables the other media type until the active link goes down. If links are active on bothmedia, the SFP-module port has priority, but you can use the media-type interface configuration command to manuallydesignate the port as an RJ-45 port or an SFP port.You can configure the speed and duplex settings consistent with the selected media type. For information on configuringinterfaces, see the switch software configuration guide.3
Product OverviewPorts and SlotsDual-Purpose Gigabit Ethernet Uplink or Downlink PortsYou can configure the dual-purpose Gigabit Ethernet uplink or downlink ports on the switch as either 10/1001000BASE-Tports or as 100/1000 Mb/s SFP-module ports. You can set the 10/100/1000BASE-T ports to autonegotiate, or you canconfigure them as fixed 10, 100, or 1000 Mb/s (Gigabit) Ethernet ports.By default, the switch selects the medium for each dual-purpose port (10/100/1000BASE-T or SFP). When a link isachieved on one media type, the switch disables the other media type until the active link goes down. If links are activeon both media, the SFP-module port has priority, but you can use the media-type interface configuration command tomanually designate the port as an RJ-45 port or an SFP port.You can configure the speed and duplex settings consistent with the selected media type. For information on configuringinterfaces, see the switch software configuration guide.Management PortsYou can connect the switch to a PC running Microsoft Windows or to a terminal server through either the RJ-45 consoleport or the USB mini-Type B console port, also referred to as the USB-mini console port. These ports use the followingconnectors: RJ-45 console port uses an RJ-45-to-DB-9 female cable. USB-mini console port (5-pin connector) uses a USB Type A-to-5-pin mini-Type B cable.The USB-mini console interface speeds are the same as the RJ-45 console interface speeds.To use the USB-mini console port, you must install the Cisco Windows USB device driver on the device that is connectedto the USB-mini console port and that is running Microsoft Windows.Note: For information about downloading the Cisco USB device driver, see Installing the Cisco Microsoft Windows XP,2000, Vista, 7, 8, and 10 USB Device Driver, page 48.With the Cisco Windows USB device driver, connecting and disconnecting the USB cable from the console port does notaffect Windows HyperTerminal operations. Mac OS X or Linux require no special drivers.Note: The 5-pin mini-Type B connectors resemble the 4-pin mini-Type B connectors, but they are not compatible. Useonly the 5-pin mini-Type B. See Figure 2 on page 4.USB Mini-Type B Port253163Figure 2The configurable inactivity timeout reactivates the RJ-45 console port if the USB-mini console port is activated, but noinput activity occurs for a specified time period. When the USB-mini console port deactivates due to a timeout, you canrestore its operation by disconnecting and reconnecting the USB cable. For information on using the CLI to configure theUSB-mini console interface, see the switch software guide.4
Product OverviewPower ConnectorsPower ConnectorsDC Power ConnectorYou connect the DC power to the switch through the front panel connectors. The switch has a dual-feed DC powersupply; two connectors provide primary and secondary DC power (DC-A and DC-B). The DC power connectors are nearthe top right of the front panel. See Figure 1 on page 2. Each power connector has an LED status indicator.The switch power connectors are attached to the switch chassis. Each power connector has screw terminals forterminating the DC power. All connectors are attached to the switch front panel with the provided captive screws.The power connector labeling is on the panel. The positive DC power connection is labeled “ ”, and the returnconnection is labeled “–”.The switch can operate with a single power source or with dual power sources. When both power sources areoperational, the switch draws power from the DC source with the higher voltage. If one of the two power sources fail,the other continues to power the switch.Alarm ConnectorYou connect the alarm signals to the switch through the alarm connector. The switch supports two alarm inputs and onealarm output relay. The alarm connector is on the bottom right of the front panel. See Figure 3 on page 5.The alarm connector provides six alarm wire connections. The connector is attached to the switch front panel with theprovided captive screws.Alarm Connector331208Figure 3Both alarm input circuits can sense if the alarm input is open or closed. The alarm inputs can be activated forenvironmental, power supply, and port status alarm conditions. From the CLI, you can configure each alarm input as anopen or closed contact.The alarm output circuit is a relay with a normally open and a normally closed contact. The switch is configured to detectfaults that are used to energize the relay coil and change the state on both of the relay contacts: normally open contactsclose, and normally closed contacts open. The alarm output relay can be used to control an external alarm device, suchas a bell or a light.See the switch software configuration guide for instructions on configuring the alarm relays.For more information about the alarm connector, see Cable and Connectors, page 595
Product OverviewAlarm ConnectorSFP Modules SupportedThe SFP modules are switch Ethernet SFP modules that provide connections to other devices. Depending on the switchmodel, these field-replaceable transceiver modules provide uplink or downlink interfaces. The modules have LCconnectors for fiber-optic connections.Refer to the IE4000 Data Sheet for details about the supported SFP Modules.6
Product OverviewAlarm ConnectorLEDsYou can use the LEDs to monitor the switch status, activity, and performance. Figure 4 on page 7 and on page 10 showthe front panel LEDs.Figure 4LEDs on the Cisco IE 4000 Switch1Dual Media port LEDs9USB mini-Type B (console) port LED2SFP module slot LEDs10Display Mode Switch310/100/1000 BASE-T downlink port LEDs11HSR/PRP4Alarm LEDs12SYNCE LED5Power connector DC-A LED13POE port status LED6Power connector DC-B LED14Duplex LED7System LED15Speed8Express Setup LEDDisplay Mode SwitchThe Display Mode Switch allows you to choose the mode you want displayed by the port LEDs (items 7, 8, and 9 inFigure 4 on page 7). The LEDs to the left of the switch indicate the chosen display mode. Each time you press the switch,the mode indicator will move from Speed, Duplex, PoE, Synce, and HSR/PRP respectively.7
Product OverviewAlarm ConnectorExpress Setup LEDThe Express Setup LED displays the express setup mode for the initial configuration.ColorSetup StatusOff (dark)Switch is configured as a managed switch.Solid greenSwitch is operating normally.Blinking greenSwitch is in initial setup, in recovery, or initial setup is incomplete.Solid redSwitch failed to start initial setup or recovery because there is no available switch port towhich to connect the management station. Disconnect a device from a switch port, and thenpress the Express Setup button.System LEDThe System LED shows whether the system is receiving power and is functioning properly.ColorSystem StatusOffSystem is not powered on.Blinking greenBoot fast is in progress.GreenSystem is operating normally.RedSwitch is not functioning properly.USB-Mini Console LEDThe USB-mini console LED shows which console port is in use. See Figure 4 on page 7 for the LED location. If youconnect a cable to a console port, the switch automatically uses that port for console communication. If you connect twoconsole cables, the USB-mini console port has priority.ColorDescriptionGreenUSB-mini console port is active.RJ-45 console port LED is not active.OffPort is not active.RJ-45 console port is active.Alarm LEDsAlarm OUTColorSystem StatusOffAlarm OUT is not configured, or the switch is off.GreenAlarm OUT is configured, no alarm detected.Blinking redSwitch has detected a major alarm.RedSwitch has detected a minor alarm.8
Product OverviewAlarm ConnectorAlarm IN1 and IN2ColorSystem StatusOffAlarm IN1 or IN2 not configured.GreenAlarm IN1 or IN2 configured, no alarm detected.Blinking redMajor alarm detected.RedMinor alarm detected.Power Status LEDsThe switch can operate with one or two DC power sources. Each DC input has an associated LED that shows the statusof the corresponding DC input. If power is present on the circuit, the LED is green. If power is not present, the LED colordepends on the alarm configuration. If alarms are configured, the LED is red when power is not present; otherwise, theLED is off.If the switch has dual power sources, the switch draws power from the power source with the higher voltage. If one ofthe DC sources fails, the alternate DC source powers the switch, and the corresponding power status LED is green. Thepower status for the failed DC source is either off or red, depending on the alarm configuration.ColorSystem StatusGreenPower is present on the associated circuit, system is operating normally.OffPower is not present on the circuit, or the system is not powered up.RedPower is not present on the associated circuit, and the power supply alarm is configured.The Power A and Power B LEDs show that power is not present on the switch if the power input drops below the lowvalid level. The power status LEDs only show that power is present if the voltage at the switch input exceeds the validlevel.For information about the power LED colors during the boot fast sequence, see Verifying Switch Operation, page 39.Port Status LEDsEach port and SFP uplink slot has a status LED, as shown in Figure 4 on page 7 and described below.ColorSystem StatusOffNo link.Solid greenLink present.Blinking greenActivity. Port is sending or receiving data.Alternatinggreen-amberLink fault. Error frames can affect connectivity, and errors such as excessive collisions, CRCerrors, and alignment and jabber errors are monitored for a link-fault indication.Solid amberPort is not forwarding. The port was disabled by management, an address violation, or STP.After a port is reconfigured, the port LED can remain amber for up to 30 seconds while STPchecks the switch for possible loops.9
Product OverviewFlash Memory CardDual-Purpose Port LEDsThe Dual Purpose LEDs show how the port is being used (Ethernet or SFP module). The LED colors have the samemeanings as for the Port Status LEDs, page 9.PoE Status LEDThe PoE STATUS LEDs are located on the front panel, next to the PoE ports (models equipped with PoE ports).The LEDsdisplay the functionality and status of the adjacent PoE ports.ColorPoE StatusOffPoE is off. If the powered device is receiving power from a non-PoE powersource, the port LED is off even if the powered device is connected to the switchport.GreenPoE is on. The port LED is green only when the PoE port is providing power.Alternating greenand amberPoE is denied because providing power to the powered device will exceed theswitch power capacity.Flashing amberPoE is off due to a fault.Caution: Noncompliant cabling or powered devices can cause a PoE portfault. Use only standard-compliant cabling to connect Cisco pre-standardIP Phones and wireless access points or IEEE 802.3af-compliant devices.You must remove any cable or device that causes a PoE fault.AmberPoE for the port is disabled. (PoE is enabled by default.)Flash Memory CardThe switch supports a flash memory card that makes it possible to replace a failed switch without reconfiguring the newswitch. The slot for the flash memory card is on the front of the switch. The flash card is hot swappable and can beaccessed on the front panel in non hazardous locations only. A cover protects the flash card and holds the card firmly inplace. The cover is hinged and closed with a captive screw. This prevents the card from coming loose and protectsagainst shock and vibration.Note: For more information on inserting and removing the flash memory card, see Installing or Removing the FlashMemory Card (Optional), page 16.Note: The replacement SD card part number is SD-IE-1GB.Rear PanelThe rear panel of the switch has a latch for installation on a DIN rail. See Figure 5 on page 11. The latch is spring-loadedto move down to position the switch over a DIN rail and return to the original position to secure the switch to a DIN rail.10
Product OverviewManagement OptionsFigure 5Cisco IE 4000 Switch Rear PanelManagement OptionsThe switch supports these management options: Cisco Network AssistantCisco Network Assistant is a PC-based network management GUI application optimized for LANs of small- andmedium-sized businesses. Using the GUI, you can configure and manage switch clusters or standalone switches.Cisco Network Assistant is available at no cost and can be downloaded from this URL:http://www.cisco.com/en/US/products/ps5931/tsd products support series home.htmlFor information on starting the Cisco Network Assistant application, see the Getting Started with Cisco NetworkAssistant guide on Cisco.com. Device ManagerYou can use Device Manager, which is in the switch memory, to manage individual and standalone switches. Thisweb interface offers quick configuration and monitoring. You can access Device Manager from anywhere in yournetwork through a web browser. For more information, see the Device Manager online help. Cisco IOS CLI11
Product OverviewNetwork ConfigurationsThe switch CLI is based on Cisco IOS software and is enhanced to support desktop-switching features. You can fullyconfigure and monitor the switch. You can access the CLI either by connecting your management station directly tothe switch management port, or a console port, or by using Telnet from a remote management station. See theswitch command reference on Cisco.com for more information. SNMP network managementYou can manage switches from a SNMP-compatible management station that is running platforms such as HPOpenView or SunNet Manager. The switch supports a comprehensive set of Management Information Base (MIB)extensions and four Remote Monitoring (RMON) groups. See the switch software configuration guide on Cisco.comand the documentation that came with your SNMP application for more information. Common Industrial ProtocolThe Common Industrial Protocol (CIP) management objects are supported. The Cisco IE 4000 can be managed byCIP-based management tools, allowing the user to manage an entire industrial automation system with one tool. PROFINET TCP/IP and RTThis switch supports PROFINET TCP/IP and RT and can be managed by Siemens' automation software such as STEP7.Network ConfigurationsSee the switch software configuration guide on Cisco.com for network configuration concepts and examples of usingthe switch to create dedicated network segments and interconnecting the segments through Gigabit Ethernetconnections.12
Switch InstallationThis chapter describes how to install your switch, verify the boot fast, and connect the switch to other devices. It alsoincludes information specifically for installations in hazardous environments.Read these topics, and perform the procedures in this order: Preparing for Installation, page 13 Installing or Removing the Flash Memory Card (Optional), page 16 Connecting to a Console Port (Optional), page 17 Connecting to Power, page 18 Installing the Switch, page 29 Connecting Alarm Circuits, page 31 Connecting Destination Ports, page 35 Verifying Switch Operation, page 39 Where to Go Next, page 39Preparing for InstallationThis section provides information about these topics: Warnings, page 13 Installation Guidelines, page 15 Verifying Package Contents, page 16WarningsThese warnings are translated into several languages in the Regulatory Compliance and Safety Information for thisswitch.Warning: Before working on equipment that is connected to power lines, remove jewelry (including rings,necklaces, and watches). Metal objects
Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is . Cisco IE 4000 Switch Software Configuration Guide Device Manager online help (available on the switch) iv
